about

Request a Sample

[email protected]

Frequently

Asked Questions
  1. Q1: Can I have a sample for testing?
    A: Yes, you can, but you need to pay.
  2. Q2: Can I add my logo on the clothing?
    A: Yes, OEM and ODM are available.
  3. Q3: Do you have inspection procedures for the products?
    A: 100% self-inspection before packing.
  4. Q4: Can I have a visit to your factory before the order?
    A: Sure, your visit is welcome at any time.
  5. Q5: How can I get after-service?
    A: We assure 2 years warranty. During this period, If any product quality issues occur, spare parts will be sent for free. But we have to charge if the problem is caused by man-made factors.

Part of an arc flash

Part of an arc flash

How to Perform an Arc Flash Study - Brainfiller

In this issue, we begin a three-part series in NFPA 70E, Standard for Electrical Safety on how to conduct an arc flash study in in the Workplace, you are about to...

Arc Flash - Paulson Manufacturing

... safety products for superior protection from arc flash , including helmets, face shields, goggles, and more. ... ArcShield Kit Replacement Parts (Standard).

Criteria for selecting arc flash protection techniques, Part 2 ...

Apr 10, 2014 ... Part 1 of this three-part series focused on arc flash incident characteristics and the causes of said incidents, as well as standards for arc flash...

6 Steps to Start an Arc Flash Prevention Program

Learn how to start an arc flash prevention program at your facility with these tips from the ... Read on for tips on how to get started on the road to arc flash prevention. ... This article may not be reproduced in part or in full without the written...

Electrical Arc Flash Hazard Protection Learning Guide

If you miss answers review the section of. Introduction to the Electrical Arc Flash Hazard Protection Standard relating to the question. Retake the self-check.

Understanding The Arc Flash Boundary Fluke

The arc flash boundary is the minimum 'safe' distance from exposed energized conductors or circuit parts that has the potential for an arc flash. The required...

Arc Flash Energy Reduction Part 1 Distance ... - Powerstudies

Arc Flash Energy Reduction Part 1 Distance is Your Friend! Arc Flash Energy is dependent upon several variables. IEEE Guide 1584-2002 and NFPA 70E.

Arc Flash Study Top 10 FAQs Part #1 - Arc Flash & Electrical Power ...

Feb 27, 2017 ... How Does Everyone Else Do This? By Jim Phillips 3-Part Series There are many frequently asked questions about performing an arc flash...

What is Arc Flash? - FRSafety

Learn about arc flash hazards and how to appropriately protect yourself. ... This is due in part to their ease in helping determine what level of PPE is required to...

Arc Flash Mitigation, Part 4 PPE & Personnel Safety

In this final installment of our four-part series on arc flash mitigation, we will look at the last line of defense against injury caused by arc flash explosions...

Implementation of arc flash mitigating solutions at industrial ... - Eaton

cement manufacturer; Implementation of an Arcflash Reduction. Maintenance System in an airlock section of a main switchroom for a minerals processing...

Arc Flash Risk Assessment Using Methodology FMECA - Eaton

An arc flash (also called flashover) is part of an arc fault, a type of electrical explosion or discharge that is the result of either a low impedance connection from air...

How to Read an Arc Flash Label - Grainger Safety Record

Learn how to read an arc flash warning label in this Grainger article about ... at a distance from an exposed energized electrical conductor or circuit part within...

The dangers of arc flash and how to protect against them ...

Jul 25, 2018 ... An arc flash is the light and heat produced as part of an arc fault. OSHA estimates that over two-thirds of all arc flash incidents are the result of...

Burn Injury Facts: Arc Flash/Blast

The intense heat and light emitted by an arc flash can cause severe burns, destroying skin and tissue. An arc ... compensation pays only a portion of lost wages.

ARC Flash Boundary & NFPA-70E Requirements PPE Program

The Arc Flash Boundary - PPE Program was developed to minimize the risk to ... limitations. Energized parts that operate at less than 50 volts to ground shall not.

What causes an arc flash and what kind of injuries can arc flash ...

An arc flash happens when electric current flows through an air gap between ... Equipment failure due to use of substandard parts, improper installation, or even...

The 7 Steps to Complete an Arc Flash Analysis - Hallam-ICS

Oct 26, 2018 ... An Arc Flash Analysis and Electrical Safety Training can greatly reduce the ... distribution road map and is a key part of an Arc Flash Analysis.

The Arc Flash Hazard Analysis Requirements Are Not New ...

Oct 8, 2014 ... Section 3-3.9.5 then outlined the arc flash protective equipment requirements. Appendix B was expanded to include Section B-5 Calculation of...

eLCOSH : Protection From Electric Shock and Arc Flash

Electricity-related hazards include electric shock and burns, arc-flash burns, arc-blast impacts, and falls. ... This can happen when you touch an energized part.

The Basics of Arc Flash - GE Industrial Solutions

deterioration or corrosion of equipment and, or parts, as well as other causes. An Arc Flash event can expel large amounts of deadly energy. The arc causes an...

Reduce Arc Flash Hazard On The Job - Optimum Safety Management

Optimum Safety Management helps companies develop arc flash hazard safety ... Electricity is such a part of our lives that we often forget about the hazards...

Arc flash - Wikipedia

An arc flash (also called a flashover), is the light and heat produced as part of an arc fault, a type of electrical explosion or discharge that results from a...

Common Electrical Hazards Including Arc Flash - OSHA

in the Workplace Including. Arc Flash. This material was produced under grant number ... On January 16, 1981, OSHA revised its Electrical standard with Part I of...

Preventing Arc Flash Injuries EHS Today

Mar 19, 2006 ... Now that we have the need for protecting our workers from arc flash hazards, what do we need to do? In the area of arc flash protection, the first...

Electrical and Arc Flash Safety Program - University of Louisville

This Electrical & Arc Flash Safety Program is founded on the principle of avoiding energized work unless it is absolutely necessary. Live parts will be...

Why an Arc Flash Study is Necessary - e-Hazard

NFPA 70E, Section 130.5 Arc Flash Analysis requires an arc flash risk assessment shall be performed to determine the risk, safety related work practices...

Arc flash hazards

and in terms of an arc flash protection boundary (FPB). Arc Flash Hazard is the term used to define the danger to people working on live parts. The Arc Flash...

Arc Flash Boundary Electrical Contractor Magazine

This is the fourth article in a series that provides a step-by-step approach for performing arc-flash hazard calculations. The first three parts appeared in the...

Key Factors to Maintaining Arc Flash Safety, Part 1

Even if an arc blast doesn't injure a person, it will damage equipment and cause downtime. Here in Part 1: four of seven arc flash safety measures. Top causes...

Arc Flash Facts Creative Safety Supply

Jul 14, 2016 ... The arc flash is a part of an arc fault, which is an example of an electrical explosion caused by a low-impedance connection that goes through...

Leonard Crawford Electric Arc Flash Studies / NFPA 70E

An Arc Flash is an electrical explosion due to a fault condition or short circuit when ... Part II 2-1.3.3 regarding Arc Flash Analysis states that a "Flash Hazard...

Webinar Top 10 Most Common Errors in Arc Flash ...

During part 1 of this 2-part series, Jim covered the first 5 most frequent beginner arc flash errors. This refresher covers the next 5 most common errors in arc flash...

Four Takeaways from Experiencing a Live Arc Flash Demonstration

Exploring the arc flash enabled a better understanding of this electrical ... Specifying arc rated (AR) / flame resistant fabric is a major part of building a program.